Custom verification kits for every PCB revision.

American company · San Francisco, CABacked by Combinator

Agonic AI Instant quote

Comparison

Verification kit vs. test fixture, flying probe and manual bench testing

There are several ways to test a printed circuit board assembly. This page explains what each one is good at, and where a custom verification kit fits beside them.

Updated November 15, 2026 · Markdown version

What are the ways to test a PCB assembly?

MethodWhat it isBest atWhat it costs you
Manual bench bring-upAn engineer probes the board by hand with a multimeter and oscilloscope.The first board of a new design, and chasing an unknown fault.Engineer time on every unit. Results depend on who probed and what they wrote down.
Flying probeA machine moves a few probes across the unpowered board. No fixture is needed.Finding assembly defects (opens, shorts, wrong or missing parts) on prototypes and small batches.Slow per board. Mostly tests the board unpowered, so it does not show how the circuit behaves.
In-circuit test (bed of nails)A fixture of spring probes contacts every test pad at once, on a dedicated tester.Finding assembly defects quickly at production volume.A custom fixture and test program for each board, and a tester to run it. Usually done by the assembler.
Boundary scan (JTAG)Chips with a JTAG port test the connections between themselves.Digital connections under BGAs and other pins you cannot probe.Only covers parts on the scan chain. Says little about analog, power or high-speed behavior.
Custom functional test fixtureA fixture and scripts your test engineers build to power the board and check that it works.Proving each unit works before it ships.Test-engineering work for each board, often started after the boards arrive.
Agonic verification kitA custom interposer board and probe dock built for one board revision. Your bench instruments plug in, and an AI agent runs the tests and writes the report.Powered verification of every unit and revision, from bring-up through production, on instruments you already own.The kit price (see Pricing). The kit is built while your PCB is in fab.

These methods answer different questions. Flying probe and in-circuit test ask "was it assembled correctly?". Bring-up, functional test and a verification kit ask "does this board work as designed?". Many teams use one of each.

How is a verification kit different from a bed-of-nails fixture?

Both hold the board against spring probes. The difference is what the probes connect to and what is tested.

  • A bed-of-nails in-circuit fixture connects the board to a dedicated in-circuit tester, which checks components and connections, mostly with the board unpowered.
  • An Agonic kit connects the board to your own bench instruments through a custom interposer board. The board is powered, and the tests measure how it behaves: rails and sequencing, impedance, high-speed eye diagrams, timing, and noise under load.

How is it different from building our own test fixture?

A functional test fixture built in-house is designed, wired and scripted by your test engineers, and that work usually starts once the design is stable. An Agonic kit is designed from your schematic and layout and built while the PCB is in fab, so it is on your bench when the first boards arrive. The same tests and fixtures then follow the board into production.

How is it different from manual bring-up?

Manual bring-up measures one point at a time, by hand, on each board. With a kit, your instruments plug in once, the agent runs the same tests on every unit, and each unit gets a written report with the measured value, the limit and the result for every test. You can compare units and revisions because they were measured the same way.

Manual probing is still the right tool for a one-off measurement or an unexpected fault. The PCB bring-up checklist lists the steps.

When does a verification kit fit?

A kit fits when:

  • You have boards coming back from fab or assembly and want them tested on the first day.
  • More than a handful of units need the same checks.
  • The board will go to production, and you want the bring-up tests to carry over.
  • You want a written record of what was measured on each unit.

A kit is built for one board revision. If you are probing a single prototype once, manual bring-up may be enough.

Does a kit replace in-circuit test or flying probe at my assembler?

Not necessarily. Those find assembly defects at the assembler, before the boards reach you. A verification kit checks that the powered board works as designed, at your bench or on your production line. They work well together.

What does a kit cost compared with a fixture?

An Agonic kit is priced from counts for your board, and the price is shown before you order: a typical kit (50 test points, 8 instrument connections) is $1,925, or $962.50 with the early-partner coupon. See Pricing or use the instant quote. It uses the instruments you already have, so there is no tester to buy.