Custom verification kits for every PCB revision.

Coupons: up to 50% off American company · San Francisco, CA Backed by Combinator

Agonic AI

Automated PCB verification, custom-built for each revision.

Agonic builds a custom interposer board and probe dock for every revision of your board. Your bench instruments plug into one end, your board into the other. An AI agent runs the tests and writes the verification report.

Get instant quote

Your files go with your order and are covered by the Design Data Terms.

Top view of the kit: an Agonic interposer board wired to a probe dock, with a rigid-flex vision board under the probe plate.
1 2 3 4
  1. 1Custom interposer board
  2. 2Custom probe plate
  3. 3Your PCB
  4. 4Probe dock

How it works

From design files to a tested board in four steps.

  1. Upload your design files

    The schematic and layout for one board revision.

  2. Review the kit and test plan

    See the probe plate, the mating plugs and the checks for your board.

  3. We build while you fab

    The interposer board and probe dock are built while your PCB is in fab.

  4. Plug in and run

    Your instruments plug in once. The agent runs the tests and writes the report.

See it run on an example board

Coupons

A limited number of coupons. EARLYPARTNER is already applied to your quote.

50%OFF

Limited number of coupons

Early partner

Half off your first kit, up to $2,000 off. Then 20% off each of your next 5 kits.

EARLYPARTNER
Terms

One per company. As an early partner we ask for a feedback call after each kit, your logo on our site, and a case study you approve. The next 5 kits are 20% off, up to $1,000 off each, when ordered within 12 months of the first. Applies to the kit price we confirm after design review, not to software, shipping or taxes. Cannot be combined with another coupon.

40%OFF

Limited number of coupons

First kit

40% off the first kit you order, up to $1,500 off.

FIRSTKIT
Terms

For companies that have not ordered a kit before. One per company. Applies to the kit price we confirm after design review, not to software, shipping or taxes. Cannot be combined with another coupon.

Instant kit quote

Enter the counts for your board and watch the price. Add your design files to order.

The schematic and layout for one board revision; a BOM is optional. The files go with your order, and we confirm the counts at design review. Up to 20 files, 90 MB in total.

Files for this kitNone yet

  • No files yet. Drop them here, or use the button.
Handled under the Design Data Terms. Do not upload ITAR-controlled or EAR-listed designs.

The counts for your board

Signal and power nets to probe. Ground probes are included.

$15050 × $3

One per bench port you plug in: a supply channel, a multimeter, each scope channel, an analyzer port, a programmer.

$808 × $10

Ribbon (IDC) and flex (FFC or FPC) connectors on your board that the dock reaches signals through.

$0 

Special requirements

Leave at 0 if none apply

High-voltage and high-current points are also counted in Test points above.

Test points that can exceed 60 V DC. 60 V is the line we use for pricing, not a rating. Above 1,000 V is confirmed at design review.
points above 60 V

$0 

High currentPoints where the dock supplies or loads the board. Points that are only measured do not count.
points at 2 to 10 A points above 10 A

$0 

High speed and RFSignals probed through coax (a differential pair is 2) and RF ports. Each comes out on its own SMA. Do not count these as test points.
high-speed signals RF ports

$0 

Two-sided probingA second probe plate for the other side of the board. Up to 10 points there are in the base kit.

$0 

Follow a unit from the bench to the report

Pick an example board and step through a verification run.

See how Agonic debugs a board in minutes.

A batch of your camera boards just came back from assembly. Walk through how Agonic plugs into your bench, tests units, and finds the faults that only show up on a MIPI link.

The same checks run on avionics, lidar, RF and eval boards: rails and sequencing, impedance, high-speed eyes, timing, and noise under load.

Oscilloscope4 ch · 8 GHz
Stop
Verification report
Unit
–
Board
VB-3 rev B
Plan
Bring-up v0.9
Firmware
0.9.1 · bitstream 0.9
#TestMeasuredLimitResult

Interactive illustration. Readings are simulated.

Ready the day your boards arrive

The kit is built while your PCB is in fab, and the same tests and fixtures follow the board into production.

Without Agonic

In fab Build a fixture, probe by hand Build production tests and fixtures Production

With Agonic

In fab Tests and probe dock built Tested day one ProductionSame tests, same fixtures Faster to production

Your design stays yours

How we handle your files is written into binding Design Data Terms, which apply to every upload.

Confidential, never sold

Your design stays confidential and is never sold.

Deleted on request

Ask, and we delete it from our active systems within 30 days.

Export controlDo not send ITAR-controlled technical data or EAR-listed technology unless we have agreed in writing to receive it. This section is a summary; the Design Data Terms are the commitments that bind us.

Boards coming back from fab in the next 90 days?

Get a quote for the kit, or plan a pilot with us.

Company
Agonic AI Inc.
Headquarters
San Francisco, California, USA
Backed by
Combinator
Contact
[email protected]

Book a time to plan your PCBA verification pilot

Loading available times

Your cart

Your cart is empty. Add your design files to a quote, then press Add to cart.

    Order total$0We confirm the price after design review. You approve any change before we build. Shipping, taxes and duties are not included.