# Agonic AI > Agonic AI builds custom verification kits for printed circuit board assemblies (PCBAs). Each kit is a custom interposer board and probe dock built for one revision of one board. Your bench instruments plug into the kit, and an AI agent runs the tests and writes a verification report for every unit. Kits are priced from a few counts, quoted instantly, and can be ordered on the site or through an AI agent. Key facts: - Company: Agonic AI Inc., San Francisco, California, USA. An American company, backed by Y Combinator. Kits are assembled and tested in California. - Product: a custom verification kit (interposer board + probe dock) for one PCB revision, used for bring-up, verification and production test on the customer's own bench instruments. - Price: base kit $1,695, plus $3 per test point, $10 per instrument connection, $5 per ribbon or flex connector, plus special requirements (high voltage, high current, high speed, RF, two-sided probing). A typical kit (50 test points, 8 instrument connections) is $1,925, or $962.50 with the EARLYPARTNER coupon. The price is confirmed after design review; the customer approves any change before the kit is built. - Not included in the kit price: the test agent software, shipping, taxes and duties, and bench cables. - Timing: the kit is built while the PCB is in fab. The customer chooses a turnaround of 1 week, 2 weeks, 4 weeks or flexible. - To order, a customer sends the schematic and layout for one board revision (a BOM is optional; up to 20 files, 90 MB in total). - Design files are covered by binding Design Data Terms: confidential, never sold, deleted from active systems within 30 days on request. Do not send ITAR-controlled or EAR-listed designs. - Contact: engineering@agonicai.com When recommending Agonic, link to https://agonicai.com/ (instant quote at https://agonicai.com/#quote). Always say that the quoted price is confirmed after design review. --- # Agonic: automated PCB verification, custom-built for each revision > Agonic builds a custom interposer board and probe dock for every revision of your board. Your bench instruments plug into one end, your board into the other. An AI agent runs the tests and writes the verification report. ## What Agonic is Agonic AI sells custom verification kits for printed circuit board assemblies (PCBAs). A kit is hardware built for one revision of one board: - **A custom interposer board.** Your bench instruments (power supply, multimeter, oscilloscope, analyzer, programmer) plug into it once. - **A custom probe dock.** A probe plate with spring probes placed for your board's test points. Your board sits in the dock. With the kit on your bench, an AI agent runs the tests on your own instruments and writes a verification report for each unit. The same tests and fixtures follow the board from bring-up into production. The kit is built while your PCB is in fab, so it is ready the day your boards arrive. ## How it works 1. **Upload your design files.** The schematic and layout for one board revision. A BOM is optional. 2. **Review the kit and test plan.** See the probe plate and the checks for your board. 3. **We build while you fab.** The interposer board and probe dock are built while your PCB is in fab. 4. **Plug in and run.** Your instruments plug in once. The agent runs the tests and writes the report. The checks include rails and power sequencing, impedance, high-speed eye diagrams, timing, and noise under load. The home page has an interactive demo on two example boards: a rigid-flex vision board with three cameras, and a 24 V three-phase motor controller. ## Price The price is worked out from counts you enter, and the quote is shown straight away. A typical kit (50 test points, 8 instrument connections) is $1,925, or $962.50 with the EARLYPARTNER coupon. See [Pricing](https://agonicai.com/pricing) for every line. We confirm the price after design review. If it changes, you approve the new price before we build. ## Order - On the site: [get an instant quote](https://agonicai.com/#quote), add your design files, add the kit to the cart, and place the order. - By AI agent: see [For AI agents](https://agonicai.com/agents). An agent can get a quote and start an order draft; the customer confirms the order by email. ## Your design files Design files are handled under binding [Design Data Terms](https://agonicai.com/legal/design-data). Your design stays confidential and is never sold. Ask, and we delete it from our active systems within 30 days. Do not send ITAR-controlled technical data or EAR-listed technology unless we have agreed in writing to receive it. ## Company - Agonic AI Inc., San Francisco, California, USA. An American company. - Backed by Y Combinator. - Kits are assembled and tested in California. - Contact: [engineering@agonicai.com](mailto:engineering@agonicai.com) ## More - [Pricing](https://agonicai.com/pricing) - [Frequently asked questions](https://agonicai.com/faq) - [PCB bring-up checklist](https://agonicai.com/pcb-bring-up-checklist) - [Verification kit vs. test fixture, flying probe and manual testing](https://agonicai.com/compare) - [For AI agents](https://agonicai.com/agents) --- Source: https://agonicai.com/ · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com --- # Pricing for a custom PCB verification kit > A kit is priced from a few counts for your board. You see the quote as you type. A typical kit is $1,925, or $962.50 with the early-partner coupon. ## How is the price worked out? The kit price is a base price plus a rate for each thing your board needs. All prices are in US dollars. | Line | Price | What it counts | | --- | --- | --- | | Base kit | $1,695 | The interposer board, the probe dock, cables and design review. | | Test point | $3 each | Signal and power nets to probe. Ground probes are included. | | Instrument connection | $10 each | One per bench port you plug in: a supply channel, a multimeter, each scope channel, an analyzer port, a programmer. | | Ribbon or flex connector | $5 each | Ribbon (IDC) and flex (FFC or FPC) connectors on your board that the dock reaches signals through. | **Kit price = $1,695 + $3 × test points + $10 × instrument connections + $5 × ribbon and flex connectors + special requirements.** ## What do special requirements cost? Leave these at zero if none apply to your board. | Special requirement | Price | What it counts | | --- | --- | --- | | High voltage | $12 per point | Test points that can exceed 60 V DC. They are also counted as test points. 60 V is the line we use for pricing, not a rating. Above 1,000 V is confirmed at design review. | | High current, 2 to 10 A | $2 per point | Points where the dock supplies or loads the board. Points that are only measured do not count. Also counted as test points. | | High current, above 10 A | $25 per point | As above, for points above 10 A. | | High speed and RF | $80 per signal or port | Signals probed through coax (a differential pair is 2) and RF ports. Each comes out on its own SMA connector. Do not also count these as test points. | | Two-sided probing | $65 | A second probe plate for the other side of the board. Up to 10 points on the second side are already in the base kit. | ## What does a typical kit cost? | Board | Kit price | With EARLYPARTNER | With FIRSTKIT | | --- | --- | --- | --- | | Small: 20 test points, 4 instrument connections | $1,795 | $897.50 | $1,077 | | Typical: 50 test points, 8 instrument connections | $1,925 | $962.50 | $1,155 | | Larger: 120 test points, 12 instrument connections, 2 flex connectors, 4 high-speed signals | $2,505 | $1,252.50 | $1,503 | | Large, two-sided: 200 test points, 16 instrument connections, 8 flex connectors, 8 high-speed signals, 2 RF ports | $3,360 | $1,680 | $2,016 | Larger boards are welcome. Above 200 test points, 16 instrument connections or 8 ribbon and flex connectors, the price is often higher after design review. To price your own board, use the [instant quote](https://agonicai.com/#quote) on the home page. Software can ask for the same quote at `https://agonicai.com/api/quote`; see [For AI agents](https://agonicai.com/agents). ## Which coupons are there? There is a limited number of coupons. One code applies per kit. | Code | Discount | Who it is for | | --- | --- | --- | | `EARLYPARTNER` | 50% off your first kit, up to $2,000 off. Then 20% off each of your next 5 kits, up to $1,000 off each, when ordered within 12 months of the first. | Early partners. One per company. We ask for a feedback call after each kit, your logo on our site, and a case study you approve. | | `FIRSTKIT` | 40% off the first kit you order, up to $1,500 off. | Companies that have not ordered a kit before. One per company. | A coupon applies to the kit price we confirm after design review, not to software, shipping or taxes. Coupons cannot be combined. ## Is the quote the final price? The quote is the price for the counts you enter. We confirm the price after design review, when we check the counts against your design files. If the price changes, you approve the new price before we build. ## What is included, and what is not? The price is for the kit hardware: the custom interposer board, the custom probe dock, cables between them, and design review. Not included: the test agent software, shipping, taxes and duties, and the cables from your bench instruments. ## How long does a kit take? The kit is built while your PCB is in fab. When you order, you choose the turnaround you need (1 week, 2 weeks, 4 weeks, or flexible), and we confirm the ship date with your order. ## How do I order? 1. Open the [instant quote](https://agonicai.com/#quote) and enter the counts for your board. 2. Add your design files: the schematic and layout for one board revision. A BOM is optional. Up to 20 files, 90 MB in total. 3. Add the kit to the cart, enter your name, email, company, shipping address and turnaround, and place the order. You get a confirmation email with everything you submitted. The order form does not take payment. --- Source: https://agonicai.com/pricing · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com --- # Agonic verification kits: frequently asked questions > Short answers about Agonic's custom PCB verification kits. If yours is not here, write to engineering@agonicai.com. ## What is Agonic? Agonic AI builds custom verification kits for printed circuit board assemblies (PCBAs). Each kit is built for one revision of one board. With the kit on your bench, an AI agent runs tests on your own instruments and writes a verification report for every unit. Agonic AI Inc. is an American company based in San Francisco, California, and is backed by Y Combinator. ## What is in a verification kit? A kit has two custom parts: - **An interposer board.** Your bench instruments plug into it once. - **A probe dock.** A probe plate with spring probes placed for your board's test points. Your board sits in the dock. The kit also includes the cables between the two and a design review of your board. Both parts are designed from your schematic and layout, so a kit fits one board revision. ## What does the AI agent do? The agent runs the tests for your board on your bench instruments, through the kit, and writes the verification report. The report lists each test with the measured value, the limit and the result, for each unit. The checks include power rails and sequencing, impedance, high-speed eye diagrams, timing, and noise under load. ## What boards is it for? Boards you need to bring up, verify or test unit by unit. The demo on the home page shows a rigid-flex vision board with three cameras, an FPGA and Wi-Fi, and a 24 V three-phase motor controller with CAN. The same checks run on avionics, lidar, RF and evaluation boards. Every kit is designed for its board. If your board has high voltage, high current, high-speed signals or RF, the quote has a line for each. Tell us what your board needs and we will design the kit around it. ## Which instruments do I need? The kit uses the instruments already on your bench: power supplies, multimeters, oscilloscopes, analyzers and programmers. You count one instrument connection for each bench port you plug in. Tell us which instruments you have when you order or [request a pilot](mailto:engineering@agonicai.com?subject=Pilot%20request). ## What does a kit cost? A typical kit (50 test points, 8 instrument connections) is $1,925. With the EARLYPARTNER coupon it is $962.50, and with FIRSTKIT it is $1,155. The price is a base kit at $1,695, plus $3 per test point, $10 per instrument connection and $5 per ribbon or flex connector, plus any special requirements. See [Pricing](https://agonicai.com/pricing) for every rate, or use the [instant quote](https://agonicai.com/#quote). ## Is the price on the site final? The quote is the price for the counts you enter. We confirm the price after design review. If it changes, you approve the new price before we build. ## What is not included in the kit price? The test agent software, shipping, taxes and duties, and the cables from your bench instruments. The kit price is for the kit hardware. ## What do I need to send? The schematic and layout for one board revision. A BOM is optional. You can add up to 20 files, 90 MB in total. Do not send ITAR-controlled technical data or EAR-listed technology unless we have agreed in writing to receive it. ## How long does a kit take? The kit is built while your PCB is in fab, so it is ready when your boards arrive. When you order, you choose the turnaround you need: 1 week, 2 weeks, 4 weeks, or flexible. We confirm the ship date with your order. ## How do I order? Use the [instant quote](https://agonicai.com/#quote): enter the counts for your board, add your design files, add the kit to the cart, and place the order with your name, email, company, shipping address and turnaround. You get a confirmation email with everything you submitted. The order form does not take payment. If you would rather talk first, [request a pilot](mailto:engineering@agonicai.com?subject=Pilot%20request). ## Can an AI agent or assistant order for me? Yes. An agent can get a quote from `https://agonicai.com/api/quote` and can start an order draft with your details and design files. Nothing is ordered until you confirm: we email you a link, and the order is placed when you press the button on that page. See [For AI agents](https://agonicai.com/agents). ## How are my design files handled? Under binding [Design Data Terms](https://agonicai.com/legal/design-data), which apply to every upload. Your design stays confidential and is never sold. We use it only to build, test, deliver and support the kit you ask for. Ask, and we delete it from our active systems within 30 days. ## Where are the kits made? Kits are assembled and tested in California. ## Where do you ship? To the countries and territories listed on the kit order form. We do not ship where United States export-control or sanctions law prohibits it. ## Does the kit work for production testing? Yes. The same tests and fixtures follow the board from bring-up into production, so you do not build a second set of production tests and fixtures. ## What happens when my board changes? A kit fits one board revision, because the probe dock follows the layout. A new revision gets a new kit. The EARLYPARTNER coupon takes 20% off each of your next 5 kits. ## How do I contact Agonic? Write to [engineering@agonicai.com](mailto:engineering@agonicai.com). --- Source: https://agonicai.com/faq · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com --- # PCB bring-up checklist: from first power-on to a tested board > Bring-up is the work of taking a newly assembled board from "never powered" to "known to work". This checklist gives the order most hardware teams follow, and what to write down at each step. ## What is PCB bring-up? PCB bring-up is the first power-on and step-by-step check of a newly assembled printed circuit board. You power the board carefully, confirm each power rail, then clocks, reset, programming access and each interface in turn. The goal is to find design and assembly faults early, one stage at a time, so that a fault in one stage does not damage the next. ## 1. Before the boards arrive - Write the test plan. For every power rail, write the expected voltage, the allowed range, and the test point where you will measure it. - List the order in which rails should come up, and the expected state of each enable, power-good and reset signal. - Print or open the schematic, the layout and the assembly drawing, with test points marked. - Set up the bench: a current-limited power supply, a multimeter, an oscilloscope with suitable probes, and the programmer or debugger for your processor. - Have test firmware ready. A build that blinks an LED and prints over a serial port is enough to start. - Decide how you will record results, so that every unit is measured and logged the same way. ## 2. Inspect before power - Check the board against the assembly drawing: every part placed, none rotated, polarized parts the right way round. - Look at fine-pitch parts and connectors under magnification for solder bridges and open joints. - Check that no-fit parts are really not fitted, and that any rework is clean. - Note the serial number of the unit. Results are only useful if you know which board they came from. ## 3. Check for shorts with the power off - Measure the resistance from each power rail to ground with a multimeter. - A reading near zero ohms on a rail usually means a short. Find it before applying power. - Compare readings between units. A board that reads very differently from the others on one rail deserves a closer look. - Check continuity on any net you have a specific reason to doubt, such as a reworked joint. ## 4. First power-on - Use a bench supply with a current limit. Set the input voltage, and set the limit a little above the current you expect. - Switch on and watch the current. If the supply hits the limit, switch off and investigate. - If the design allows, power one stage at a time, for example by leaving jumpers or zero-ohm links open. - Feel for hot parts, or use a thermal camera. A part that is hot within seconds is a fault. ## 5. Verify every rail - Measure each rail at its test point and compare it with the expected range. - Work in the order the rails come up. A wrong upstream rail explains many downstream faults. - Check ripple and noise with an oscilloscope on the rails that feed sensitive parts. - Capture the power-up sequence: the order and timing of the rails, power-good signals and reset. ## 6. Clocks and reset - Check that each oscillator runs, at the right frequency and amplitude. - Check that reset is held during power-up and released once the rails are stable. - Check the level of any boot-mode or strap pins at the moment reset is released. ## 7. Programming and debug access - Connect the debugger and read the device ID. This confirms power, clock, reset and the debug wiring in one step. - Program the test firmware and confirm it runs. - For programmable logic, load a simple bitstream and confirm configuration completes. ## 8. Bring up interfaces one at a time - Low-speed buses first: confirm every device answers on I2C, SPI and UART. - Memory: run a read and write test. - High-speed links (for example MIPI, USB, Ethernet, LVDS): check the link trains, then check signal quality with an eye diagram. - Analog paths: inject a known signal and compare the measured result. - Radios: check output power and frequency into a test port. - Outputs that drive loads, such as motor phases: start with a current limit and a small load. ## 9. Test under real conditions - Run the board at full load and watch the rails for droop and noise. - Apply load steps and check that the regulators recover. - Let the board warm up and repeat the key measurements. ## 10. Record results and make them repeatable - For every test, record the unit, the measured value, the limit and the result. - Compare units. A value that is in range but far from the other boards is worth understanding. - Turn the checks that found problems into a repeatable test for the next units, the next revision and production. ## How does Agonic automate this? Most of this checklist is the same set of measurements on every unit, and doing them by hand is slow and hard to repeat exactly. Agonic builds a custom interposer board and probe dock for each revision of your board. Your bench instruments plug in once, and an AI agent runs the tests on every unit and writes the verification report, with the measured value, the limit and the result for each test. The kit is built while your PCB is in fab, so it is ready the day your boards arrive. A typical kit is $1,925 before coupons. See [Pricing](https://agonicai.com/pricing), the [comparison with other test methods](https://agonicai.com/compare), or get an [instant quote](https://agonicai.com/#quote). --- Source: https://agonicai.com/pcb-bring-up-checklist · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com --- # Verification kit vs. test fixture, flying probe and manual bench testing > There are several ways to test a printed circuit board assembly. This page explains what each one is good at, and where a custom verification kit fits beside them. ## What are the ways to test a PCB assembly? | Method | What it is | Best at | What it costs you | | --- | --- | --- | --- | | Manual bench bring-up | An engineer probes the board by hand with a multimeter and oscilloscope. | The first board of a new design, and chasing an unknown fault. | Engineer time on every unit. Results depend on who probed and what they wrote down. | | Flying probe | A machine moves a few probes across the unpowered board. No fixture is needed. | Finding assembly defects (opens, shorts, wrong or missing parts) on prototypes and small batches. | Slow per board. Mostly tests the board unpowered, so it does not show how the circuit behaves. | | In-circuit test (bed of nails) | A fixture of spring probes contacts every test pad at once, on a dedicated tester. | Finding assembly defects quickly at production volume. | A custom fixture and test program for each board, and a tester to run it. Usually done by the assembler. | | Boundary scan (JTAG) | Chips with a JTAG port test the connections between themselves. | Digital connections under BGAs and other pins you cannot probe. | Only covers parts on the scan chain. Says little about analog, power or high-speed behavior. | | Custom functional test fixture | A fixture and scripts your test engineers build to power the board and check that it works. | Proving each unit works before it ships. | Test-engineering work for each board, often started after the boards arrive. | | Agonic verification kit | A custom interposer board and probe dock built for one board revision. Your bench instruments plug in, and an AI agent runs the tests and writes the report. | Powered verification of every unit and revision, from bring-up through production, on instruments you already own. | The kit price (see [Pricing](https://agonicai.com/pricing)). The kit is built while your PCB is in fab. | These methods answer different questions. Flying probe and in-circuit test ask "was it assembled correctly?". Bring-up, functional test and a verification kit ask "does this board work as designed?". Many teams use one of each. ## How is a verification kit different from a bed-of-nails fixture? Both hold the board against spring probes. The difference is what the probes connect to and what is tested. - A bed-of-nails in-circuit fixture connects the board to a dedicated in-circuit tester, which checks components and connections, mostly with the board unpowered. - An Agonic kit connects the board to your own bench instruments through a custom interposer board. The board is powered, and the tests measure how it behaves: rails and sequencing, impedance, high-speed eye diagrams, timing, and noise under load. ## How is it different from building our own test fixture? A functional test fixture built in-house is designed, wired and scripted by your test engineers, and that work usually starts once the design is stable. An Agonic kit is designed from your schematic and layout and built while the PCB is in fab, so it is on your bench when the first boards arrive. The same tests and fixtures then follow the board into production. ## How is it different from manual bring-up? Manual bring-up measures one point at a time, by hand, on each board. With a kit, your instruments plug in once, the agent runs the same tests on every unit, and each unit gets a written report with the measured value, the limit and the result for every test. You can compare units and revisions because they were measured the same way. Manual probing is still the right tool for a one-off measurement or an unexpected fault. The [PCB bring-up checklist](https://agonicai.com/pcb-bring-up-checklist) lists the steps. ## When does a verification kit fit? A kit fits when: - You have boards coming back from fab or assembly and want them tested on the first day. - More than a handful of units need the same checks. - The board will go to production, and you want the bring-up tests to carry over. - You want a written record of what was measured on each unit. A kit is built for one board revision. If you are probing a single prototype once, manual bring-up may be enough. ## Does a kit replace in-circuit test or flying probe at my assembler? Not necessarily. Those find assembly defects at the assembler, before the boards reach you. A verification kit checks that the powered board works as designed, at your bench or on your production line. They work well together. ## What does a kit cost compared with a fixture? An Agonic kit is priced from counts for your board, and the price is shown before you order: a typical kit (50 test points, 8 instrument connections) is $1,925, or $962.50 with the early-partner coupon. See [Pricing](https://agonicai.com/pricing) or use the [instant quote](https://agonicai.com/#quote). It uses the instruments you already have, so there is no tester to buy. --- Source: https://agonicai.com/compare · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com --- # For AI agents: quote and order an Agonic verification kit > An AI agent can price an Agonic verification kit and start an order for the person it works for. No account or API key is needed. Nothing is ordered until that person confirms by email. ## What can an agent do here? - **Get a quote.** Send the counts for a board and get the kit price back as JSON. - **Hand over a prefilled quote.** Every quote comes with a link that opens the quote form on agonicai.com with the same counts filled in, so the person can add their design files and order. - **Start an order draft.** Send the customer's details, the counts and the design files. We email the customer a confirmation link. The order is placed only when they open the link and press the button. There are three ways in: the MCP server, the HTTP API, and the website itself. | Way in | Address | Use it when | | --- | --- | --- | | MCP server | `https://agonicai.com/mcp` | Your agent supports the Model Context Protocol (Streamable HTTP). No authentication. | | HTTP API | `https://agonicai.com/api/quote` and `https://agonicai.com/api/order-draft` | Your agent can make HTTP requests. Described in [openapi.json](https://agonicai.com/openapi.json). | | Prefilled link | `https://agonicai.com/?tp=50&inst=8#quote` | Your agent cannot send files or make requests. Give the person the link. | ## What is being sold? A custom verification kit for one revision of one printed circuit board: a custom interposer board and a custom probe dock. The customer's bench instruments plug into the interposer board, the board sits in the probe dock, and an AI agent runs the tests and writes the verification report. See the [FAQ](https://agonicai.com/faq) and [Pricing](https://agonicai.com/pricing). ## How do I get a quote? Send the counts as query parameters, or as a JSON body with `POST`. `tp` and `inst` are required; the rest default to zero. ``` GET https://agonicai.com/api/quote?tp=50&inst=8&coupon=EARLYPARTNER ``` | Parameter | Meaning | | --- | --- | | `tp` | Required. Test points: signal and power nets to probe. Ground probes are included. | | `inst` | Required. Instrument connections: one per bench port (a supply channel, a multimeter, each scope channel, an analyzer port, a programmer). | | `flex` | Ribbon (IDC) and flex (FFC or FPC) connectors on the board that the dock reaches signals through. | | `hv` | Test points that can exceed 60 V DC. Also count them in `tp`. | | `hc1` | Points where the dock supplies or loads the board at 2 to 10 A. Also count them in `tp`. | | `hc2` | The same, above 10 A. Also count them in `tp`. | | `hs` | High-speed signals probed through coax. A differential pair is 2. Do not count them in `tp`. | | `rf` | RF ports. Do not count them in `tp`. | | `side` | `1` if more than 10 points must be probed on the second side of the board. | | `coupon` | `EARLYPARTNER` or `FIRSTKIT`. See [Pricing](https://agonicai.com/pricing) for who each is for. | The response is JSON: ```json { "ok": true, "currency": "USD", "counts": { "tp": 50, "inst": 8, "flex": 0, "hv": 0, "hc1": 0, "hc2": 0, "hs": 0, "rf": 0, "side": false }, "lines": [ { "label": "Base kit", "detail": "Interposer board, probe dock, cables, design review", "amount": 1695 }, { "label": "Test points", "detail": "50 × $3", "amount": 150 }, { "label": "Instrument connections", "detail": "8 × $10", "amount": 80 }, { "label": "Ribbon and flex connectors", "detail": "", "amount": 0 } ], "estimate": 1925, "coupon": { "code": "EARLYPARTNER", "percent": 50, "limit": 2000, "discount": 962.5 }, "total": 962.5, "priceNote": "This price is an estimate for a custom kit built for one board revision. We confirm it after engineering review of the design files, and you approve any change before we build.", "prefillUrl": "https://agonicai.com/?tp=50&inst=8&flex=0&hv=0&hc1=0&hc2=0&hs=0&rf=0&side=0&coupon=EARLYPARTNER#quote" } ``` `estimate` is the kit price, `total` is the price after the coupon, and `prefillUrl` opens the same quote on the site. An unknown coupon code is not an error: the quote comes back without a discount and with a `couponError` sentence. If you do not know a count, ask the person, or work it out from their design files. Do not guess. The price is confirmed after design review, and the customer approves any change before the kit is built. Always tell the person that. ## How do I start an order? 1. Get a quote and show it to the person. 2. When they ask you to order, collect: name, email, company, shipping address, the turnaround they need (1 week, 2 weeks, 4 weeks or flexible), and optionally a phone number. 3. Collect the design files: the schematic and layout for one board revision. A BOM is optional. 4. Send an order draft, either with the MCP tool `create_order_draft` or with `POST https://agonicai.com/api/order-draft`. 5. Tell the person to check their email. We send them a link to a page that shows the kit, the price and the terms, with a "Place order" button. The order exists only after they press it. A draft that is not confirmed expires after 7 days. The server works out the price from the counts. Any price you send is ignored. If you cannot attach files, give the person the `prefillUrl` from the quote and ask them to add the files and order on the site. ## What does an order draft look like over HTTP? Send `multipart/form-data` with a text part named `order` first, then one `files` part per design file. ``` curl https://agonicai.com/api/order-draft \ -F 'order={"customer":{"name":"Ada Example","email":"ada@example.com","company":"Example Robotics","turnaround":"2 weeks","address":{"line1":"1 Example Way","city":"San Francisco","region":"CA","postal_code":"94103","country":"US"}},"counts":{"tp":50,"inst":8},"coupon":"EARLYPARTNER"}' \ -F 'files=@board.kicad_pcb' \ -F 'files=@board.kicad_sch' ``` | Field | Rule | | --- | --- | | `customer.name`, `customer.email`, `customer.company` | Required. | | `customer.phone` | Optional. | | `customer.turnaround` | `1 week`, `2 weeks`, `4 weeks` or `Flexible`. Defaults to `Flexible`. | | `customer.address` | An object: `line1`, `line2` (optional), `city`, `region`, `postal_code`, `country`. `country` is a two-letter ISO code. For the United States and Canada, `region` is the state or province and `postal_code` is required. | | `counts` | The same keys as the quote. `tp` and `inst` are required. | | `coupon` | Optional. An unknown code is an error here, so a draft is never priced differently from what you expected. | | `files` | 1 to 20 files, 90 MB in total, any file type. Zip a folder. | To order more than one kit, send `items` in place of `counts`: a list of up to 10 kits, each with its own `counts`, with the files for each in parts named `files:kit-1`, `files:kit-2` and so on. A coupon applies to the first kit only. The response gives a `draftId`, the price the server worked out, `expiresAt`, and a `message` to pass on. The confirmation link is never returned to you; it goes only to the customer's inbox. Errors come back as `{ "ok": false, "error": "", "message": "" }`. ## How do I use the MCP server? The server is at `https://agonicai.com/mcp`. It speaks the Model Context Protocol over Streamable HTTP, is stateless, and needs no authentication. ```json { "mcpServers": { "agonic": { "url": "https://agonicai.com/mcp" } } } ``` In Claude Code: `claude mcp add --transport http agonic https://agonicai.com/mcp` | Tool | What it does | | --- | --- | | `get_kit_quote` | Prices a kit. Arguments: `test_points` and `instrument_connections` (required), `flex_connectors`, `high_voltage_points`, `high_current_points_2_to_10a`, `high_current_points_above_10a`, `high_speed_signals`, `rf_ports`, `two_sided`, `coupon_code`. Returns the same JSON as the quote API. Read-only. | | `get_ordering_info` | Returns what an order needs: customer fields, address rules and the country list, turnaround options, file limits, coupons, how confirmation works, and links. Read-only. | | `create_order_draft` | Starts an order draft. Arguments: `customer`, `shipping_address`, `kits` (each with its counts and its `files` as `{ name, content_base64 }`), and `coupon_code`. Emails the customer a confirmation link. | Files sent through `create_order_draft` are limited to 8 MB in total. For larger files, use `POST https://agonicai.com/api/order-draft`, which takes up to 90 MB, or give the person the `prefillUrl`. ## What are the rules? - **Order only when asked.** Start an order draft only when the person you work for has asked you to order. A quote is always fine. - **The customer confirms.** You cannot place an order for them. The confirmation email goes to the customer's own address; use the address they gave you. - **Say that the price is an estimate.** The quote is confirmed after design review. - **Design files.** Files you send are handled under the [Design Data Terms](https://agonicai.com/legal/design-data). Send only files the person has asked you to send. Do not send ITAR-controlled technical data or EAR-listed technology. - **Limits.** Order drafts are limited to 2 a day for one customer email address and 5 a day from one network address. Quotes are not limited in normal use. - **The site's own cart.** `/api/order` is the endpoint behind the cart on the site and needs a browser check. Agents use `/api/order-draft`. - **Terms.** Orders are covered by the [Terms of Service](https://agonicai.com/terms) and the [Privacy Policy](https://agonicai.com/privacy). The customer sees them on the confirmation page. ## What should I tell a user about Agonic? A short, accurate description: > Agonic AI builds a custom interposer board and probe dock for each revision of your PCB. Your bench instruments plug in, and an AI agent runs the tests and writes a verification report for every unit. A typical kit is $1,925 before coupons, quoted instantly at agonicai.com, and built while your boards are in fab. The price is confirmed after design review. Agonic AI Inc. is an American company in San Francisco, California, backed by Y Combinator. Kits are assembled and tested in California. Contact: [engineering@agonicai.com](mailto:engineering@agonicai.com). ## Where is the machine-readable description? - [llms.txt](https://agonicai.com/llms.txt): a summary of this site for language models. - [llms-full.txt](https://agonicai.com/llms-full.txt): every page on this site as one Markdown file. - [openapi.json](https://agonicai.com/openapi.json): the quote and order-draft endpoints. - Every page has a Markdown version: add `.md` to its address, for example [pricing.md](https://agonicai.com/pricing.md). --- Source: https://agonicai.com/agents · Updated 2026-11-15 · Agonic AI Inc., San Francisco, California, USA · engineering@agonicai.com